Portfolio Category: Material Type

 A36 = Angle, Channel, Flat, Square, Round, Tee, Beam, Plate 1018 = Round, Square, Hex, Flat 1117 = Round, Square, Hex, Flat 12L14 = Round, Square, Hex A513 = Tube (Ornamental, DOM) A500 = Tube (Structural) A519 = Tube (CDS, HFS) A1008 = Sheet (Cold Rolled) A1011 = Sheet (Hot Rolled) A653 = Sheet (Galvanized) A53…

GALVANIZED GALVANNEALED (PAINT BONDABLE)     GALVANIZED ASTM-A653 Sheet .135 and thinner Mild Steel / Low Carbon Galvanized Coating resists corrosion Air Conditioning and Heating  and Ventilation Ducts Good Bending Welding can cause dangerous fumes Spangle = surface snowflake-like pattern Spangle can be specified "Small-Minimum" or "Large" Different manufacturers offer different Spangle Coating Thickness Designated…

TGP 1045 Chrome Rod 1045 Plow 1045 1144 Stressproof® Tul Bar / Hollow & Solid Flat / Bevel Edge Grouser Bar Railroad Rail A606 & A588 Corten® A572   1045 TGP (Turned Ground & Polished) Round Medium Carbon Steel Pump Shaft Quality (PSQ) Tolerance Used for Motor Shafts, Axles Not readily weldable Stress Relieving after welding recommended…

Plow 1045 IN STOCK FLAT BAR: 1/4" x 2" 3/8" x 4" 3/8" x 6" 1/2" x 4" 1/2" x 6" 5/8" x 4" 5/8" x 6" 3/4" x 4" 3/4" x 6" 1" x 4" 1" x 6" IN STOCK ROUND CORNER SQUARE: 2-1/4"    

   F400  F500 F400 Formalloy 400 8' x 24' Plate sizes Common for shooting targets Common for abrasion resisting agriculture and construction parts No ASTM number is designated Hardness is all the way through the plate Typical Chemical Analysis Carbon (C) = .17 Max Manganese (MN) = 1.50 Max Phosphorus (P) = .015 Max Sulphur (S)…

  4130 4140 A514 (T1®) F400 F500    4130 Tube Round Available in Round Tube Available in Cold Drawn Normalized Condition Available as Seamless Common for Sand Rail - Dune Buggy Frames Common for Race Car Frames Common for Aircraft Frames Through-Hardened Chromium Molybdenum Alloy Good Formability  Typical Chemical Analysis Carbon (C) = .28-.33 Manganese…

1095    1095 Blue Clock Spring Tempered Available as Flat and Sheet Common for Shims, Springs, Scrapers, Knives Pre-Hardened and Tempered Polished and Blued "Clock Spring" is a common name  Typical Chemical Analysis Carbon (C) = .9-1.04 Manganese (MN) = .30-.50 Phosphorus (P) = .04 Max Sulphur (S) = .05 Max Silicone (SI) = .10-.30  Typical…

O1

GRAY IRON: Contains flake graphite in matrix structures that range from all pearlite to pearlite plus ferrite. The matrix structure will influence machinability, strength, hardness and wear characteristics. In general, a fully pearlitic matrix will have the best mechanical properties and will be readily machinable. Bars containing ferrite in the matrix will be easier to…

  303  304 316 416    

2011 2024 3003  5052 6061 6063 7075 MIC-6  

  Brass C26000 Brass C36000 Copper C11000 Bronze C93200

Acetal (Delrin) UHMW ABS Urethane PTFE (Teflon) Polycarbonate (Lexan)  

 Apitong Trailer Decking PART NUMBER MATERIAL SIZE LENGTH TYPE  LBS FT ZT610-2050 Apitong Brazilian Hardwood 1-1/8" x 7" 21' Shiplap 2.72#

LEAD TIN BABBITT ZINC  (HULL ANODE)  

Fiberglass Rebar

  IN STOCK Bumper Rubber Tie Down Rubber Hardware Rubber SPECIAL ORDER  Sheet